Rennline high density front strut mounts for your 911/914 not only replace tired factory rubber pieces, but return better handling and ride quality without being overly stiff. At 25% more stiff than stock, these are a great compromise, allowing the front suspension to maintain better alignment and geometry over bumps and around corners thanks to their increased stiffness. Still at home on a race track, these will ride with a feel closer to factory than that of our more track oriented full camber plate and monoball setups.

Includes (2) strut mounts, one per side

General Fitment

This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a pvc plastic rear window like the original. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion; increased fade resistance and the tighter woven layers are made for stronger frames. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. This would replace original part # 911 563 051 00 2xw made in Germany. Sold individually. 1 necessary per car.

This item ma...(choose a part on the right to read more)

As our classics age, the original gaskets and seals become brittle and will crack. It is essential that they are replaced to prevent moisture damage and to keep interior noise at a minimum. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

View/Change Diagram

911 1970-73 - Body	911 1974-77 - Body
911 1978-83 - Body	911 1984-86 - Body
911 1987-89 - Body	912 1965-69 - Body
911 1965-69 - Body

This is the felt or velvet sealing strip that protects the outer edge of the sunroof panel. It assists in keeping out moisture and protects the panel during operation. It can become brittle and will crack overtime so it is essential that it is in good order. It can also lose the plush black appearance with wax applications. Sold individually. 1 needed per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

View/Change Diagram

911 1970-73 - Body	911 1974-77 - Body
911 1978-83 - Body	911 1984-86 - Body
911 1987-89 - Body	930 1975-77 - Body
912 1965-69 - Body	911 1989-94 - Body
911 1994-98 - Body	911 1965-69 - Body

For 7” and 9” flares.
***note: these rockers have mold parting lines that will show towards each end of the panel. These will need to be filled in and sanded smooth. As with any after market fiberglass part, finishing work is required for proper look and fit.***

Drain tubes can become clogged and will eventually lead to corrosion of the head light bucket. If you are upgrading your headlights or servicing them it is a great idea to change the drain tube. Sold individually. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

View/Change Diagram

911 1970-73 - Electrical	911 1970-73 - Electrical
911 1970-73 - Electrical	911 1987-89 - Electrical
911 1987-89 - Electrical	912 1965-69 - Electrical
912 1965-69 - Electrical	912 1965-69 - Electrical
911 1989-94 - Body	911 1989-94 - Electrical
911 1965-69 - Electrical	911 1965-69 - Electrical
911 1965-69 - Electrical

Tired of being hit in the head with your unruly visor? Put it in its place for good. Factory replacements install in seconds and will remedy the headache.

View/Change Diagram

911 1970-73 - Body	911 1974-77 - Body
911 1978-83 - Body	911 1984-86 - Body
911 1987-89 - Body	930 1975-77 - Body
912 1965-69 - Body	928 1978-82 - Body
928 1983-86 - Body	928 1987-91 - Body
928 1992-95 - Body	911 1989-94 - Body
911 1994-98 - Body	911 1965-69 - Body

From the leading blaupunkt restorer in Germany comes this factory restored blaupunkt am fm frankfurt radio. originally installed in all 1969 through 1973 Porsche 911 912 and 914 models as the premier radio option, this beautiful radio is the final addition to your pristine restoration. fully guaranteed for two years this radio does not require a core charge and is ready to install. so beautiful that it will satisfy the fussiest concours enthusiast. this is a monaural radio not stereo. please see our other listings for the radio installation kit, the radio faceplate, the ipod adaptor and the speakers

General Fitment

Does your car pull to one side when you hit the brakes or let go of the wheel? Do you notice one wheel seems to "get hot"? Are your calipers leaking or stuck even though you have cracked the bleeder nipples? You may need to rebuild your caliper(s). These factory kits include seals, piston clips, and boots; and with a little labor and paint, will look new as well. Reasonably priced, they sure beat the price of a new caliper!

View/Change Diagram

356 1960-65 - Brakes/Wheels	356 1960-65 - Brakes/Wheels
912 1965-69 - Brakes/Wheels	911 1965-69 - Brakes/Wheels

This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 058 05. We also suggest replacing your outer tie rods, we have a uniball option, our part # 96534703200sp or the OEM style, narrow body is part # 96434703200 or wide body is part # 96434703201 (qty. 2 are needed) and now is also...(choose a part on the right to read more)

This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a trapezoidal pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames, like the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German ...(choose a part on the right to read more)

Great find! This is a set of replica fuchs polished wheels complete with the Porsche center cap for all 356 c 911 912 and 914-6 models through 1977. You will love the updated look of these brilliantly polished, precisely made wheels. 5.5x15 they will easily fit a 165x15 195/65x15 or 205/60x15 tire.

General Fitment

Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more)

General Fitment

This is a very correct limited edition factory model from vw. it is not available in the united states and very hard to find. we have a stash of them coming and because of the exchange rate and shipping and duties, they will be $75 each. we are getting the last 20. anyone interested can put their order in and we will ship when they arrive. after the 20 are sold we will cut off the orders. Do not miss this once in a lifetime opportunity to own one of these commemorative models.

General Fitment

Great buy on a set of front bumper guards for all 73-74 914s. stainless steel skeleton and waterproof materials make this a bumper guard that will last for life!

This oil pipe is necessary when installing the oil line for the tensioner hose to camshaft carrier, part # 93010734714 we recommend purchasing, 1 qty. Banjo bolt n0210731 and 2 qty. Sealing rings, part # 90012311530 to complete the installation. This part is sourced in Germany to ensure quality, reliability and precise fitment. This will fit all the vehicles listed in the fitment tab and those that have been updated to pressure fed tensioners. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. For installation on the left-hand side, you will need 1 qty. Spacer, part # 93010551300 and 1 qty. Chain wheel support, part # 93010550900. For installation on the right-hand side, you will need 1 qty. Spacer, part # 93010551300 and 1 qty. Chain wheel support, part # 93010551000 sold individually. Left or right-side fitment. 2 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM part number, 965 347 032 00. Sold individually. 2 needed per car. We also suggest replacing your inner tie rod, we have a uniball option, our part # 96434705805sp (qty. 1 is needed) and now is also a good time to replace your worn out inner tie...(choose a part on the right to read more)

Does your car pull to one side when you hit the brakes or let go of the wheel? Do you notice one wheel seems to "get hot"? Are your calipers leaking or stuck even though you have cracked the bleeder nipples? You may need to rebuild your caliper(s). These factory kits include seals, piston clips, and boots; and with a little labor and paint, will look new as well. Reasonably priced, they sure beat the price of a new caliper!
Known as: gasket set for s-calliper comprising: / gasket set

View/Change Diagram

911 1970-73 - Brakes/Wheels	911 1974-77 - Brakes/Wheels
911 1974-77 - Brakes/Wheels	930 1975-77 - Brakes/Wheels
930 1975-77 - Brakes/Wheels	912 1965-69 - Brakes/Wheels
911 1965-69 - Brakes/Wheels

By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)

This is a new production of the rear view mirrors, where it does't have heaving crimping on the corner of the metal to the mirror edge, great quality manufactured product. This will fit your Porsche 911 & 912 from ' 65 - ' 67.

We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)

Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. This oil-tank will fit also to older car's ( -1983 ) with new cap 034133335d and new hose-clamp pcg51219802. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.